The content which follows on the subject of How to Install a Bathtub Yourself is quite insightful. Don't bypass it.
Setting up a bathtub isn't exactly brain surgery, but it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult task. If the old tub is readily obtainable, the job can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the new tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed job, it is far better to take into consideration using one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly aid you mount a new bath tub in your restroom if you have currently acquired a brand-new tub and also do not need to alter the setup of your previous water supply pipes.
Your devices and product list must comprise the following:
Preparing for the Installment
First of all, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to prevent strain on the bath tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the required placement. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bath tub till the spirit level checks out level.
To install taps, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water supply as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bath tub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Lastly, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the tub needs to wait until the tub has actually been made use of at least when as this will settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous type must be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, resulting in problems with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly readily available on the market. It is advisable to fit the tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog entry about A Step-by-Step Guide to Installing a Bathtub when surfing the search engines. Enjoyed reading our article? Please share it. Help someone else check it out. I value reading our article about How to Install a Bathtub Yourself.
Make An Appointment